Keller Dovetail System 135-1500 Journeyman DoveTail Jig by Keller Dovetail System
Ratting :
List Price : $159.00
Price : $131.45
Back-to-back edition.Accepts timber from 1/8 to 3/4 inches thick.No test cuts, no wasted wood.Accepts unlimited widths and sizes.15-inch precision-milled template. The Keller Dovetail System 135-1500 Journeyman DoveTail Jig is a cost-effective choice for the amateur or hobbyists doing small to midsize tasks. The back-to-back version deal withs timber 1/8 to 3/4 inches thick of any width with a single template precision-milled from phenolic plate. It can minimize traditional, variable-spaced, acute, obtuse, compound-angled, and curved dovetails, in addition to box and knuckle joints. Your jig buy features a phenolic information, standard dovetail bit, straight bit, ball-bearing template informations, and absolutely illustrated directions..
The Keller Dovetail System 135-1500 Journeyman DoveTail Jig for Sale it's best Back-to-back edition.Accepts timber from 1/8 to 3/4 inches thick.No test cuts, no wasted wood.Accepts unlimited widths and sizes.15-inch precision-milled template. The Keller Dovetail System 135-1500 Journeyman DoveTail Jig is a cost-effective choice for the amateur or hobbyists doing small to midsize tasks. The back-to-back version deal withs timber 1/8 to 3/4 inches thick of any width with a single template precision-milled from phenolic plate. It can minimize traditional, variable-spaced, acute, obtuse, compound-angled, and curved dovetails, in addition to box and knuckle joints. Your jig buy features a phenolic information, standard dovetail bit, straight bit, ball-bearing template informations, and absolutely illustrated directions..
Read more Keller Dovetail System 135-1500 Journeyman DoveTail Jig
Keller Dovetail System 135-1500 Journeyman DoveTail Jig Feature
Related Products
- Keller 135-1633 1/4-Inch Shank Dovetail Bit
- INCRA Build-It Hold Down Clamp
- Keller 135-1643 1/4-Inch Shank Straight Bit
- Bench Dog 10-035 Bench Cookie Work Grippers, 4-Pack
- MLCS 8377 15-Piece Router Bit Set with Carbide-Tipped 1/2-Inch Shanks
Customer Reviews
4.8 Out Of 5 Stars (28 Customer Reviews)Reviews for Keller Dovetail System 135-1500 Journeyman DoveTail Jig (Tools & Home Improvement) Having heard how straightforward it was to make just proper dovetail joints with the Keller device and after quite a few analysis, I offered the Journeyman Model 1500 machine. "Easy" may be a mild reach for a newcomer, however with a little bit of studying and remembering of the instructions, it all worked out ok. The instruction guide is written for their aluminum templates with a single sheet inserted for the 1500, but the course of is typically the same for each forms of templates. The 1500 requires a block of wood 2¼ x 3½ x about 18 inches on which the template is set up. I do not think these dimensions are very very important. The workpiece is clamped vertically in a vise and the block of wood is clamped on the facet of the workpiece with the template projecting over the threshold to be dovetailed. It is usually recommended you put the block on the near aspect of the workpiece so you route far from you and so the chips don't come off on your face. Keller offers two router bits - one to reduce the tails (a dovetail bit) and one for the pins (a straight bit). You reduce the tails first, then put the mating workpiece in the vise and lay the just-cut piece with the tails on the threshold (line it up just right) and scribe the inside of one of the most tail lowerouts on the brand new workpiece. Then you align the template pin side OVER the scribed lines and clamp it down. This decides what will remain while you route the pins. The first set got here out ok but had been too tight. Keller gives instructions on calm down the joint (slide the pin side of the template additional onto the backing block). I just about wore out the screws conserving the template to the block of wooden with my fiddling round to get the joints becoming the means in which I needed. The Keller device makes via dovetails, so if you need half-blind dovetails, this is now not the one you need unless there is a trick I am now not aware about. IMO I suppose through dovetails are extra dependent than half-blind as you see the artistry on each aspects of the joint. I also like the idea of not being restricted to a maximum width workpiece. I take no longere further router bits are to be had for box joints.
Reviews for Keller Dovetail System 135-1500 Journeyman DoveTail Jig (Tools & Home Improvement) This is a good jig. The backing block thickness dimension desires an adjustment with a function to make hardwood joints that don't seem to be too tight, on the opposite hand - learn other evaluates. The 3 1/2" depth isn't critical; neither is the 18" length. I recommend milling the block out of poplar, comfortable maple, or (like I did) salvaged yellow pine in an effort to get a thickness of 2 5/16" (not 2 1/4", as steered). Then set the scribed line BACK exactly 1/16" by making your individual scribe on the dovetail aspect and set your screws in. This will permit your pins to be slightly thinner than they might be with the urged dimensions. Then play with the router bit depths between 1/32" and 1/16" further (beyond your inventory thickness and the 1/2" thickness of the jig) to tremendous tune (a deeper dovetail bit will make the joint tighter).
Reviews for Keller Dovetail System 135-1500 Journeyman DoveTail Jig (Tools & Home Improvement) I've been woodworking for over two decades, and used to chop dovetails by means of hand. I regarded at the jigs but was once always delay by way of the high worth and large guides. I learn a evaluation on totally different jigs and the Keller was deemed the most simple to make use of. I offered it and could now not be happier. It took me about 5 minutes to screw the jig to a backer board, and 10 minutes later I was putting collectively the primary joint. It was once perfect. My only regret is not buying this factor 12 monthss ago. It's so simple, you do no longer even want to maintain the booklet around, because there could be now nothing truly to set up. Bit depth just isn't essential, you just set it a hair deeper than the wooden thickness. I now can buzz via a complete project's dovetails faster than I used to chop out one side with the support of hand, and they seem higher too.
